Factory-Direct Privacy Gate GuideAn aluminum privacy gate can block direct views into a property without creating the maintenance problems of a large wood gate. The design can use narrow ALU20 slats, wider ALU40 profiles, no-gap tongue-and-groove panels, angled AeroLouver blades, flush cladding, laser-cut inserts, translucent acrylic or a combination of several systems.Privacy is not created by color alone. It comes from profile width, gap, slat depth, viewing angle, gate height, bottom clearance and the relationship between the gate and the surrounding fence or walls. As privacy increases, wind surface, frame demand, hinge load, post reactions and operator requirements can also increase.This 2026 guide explains how to choose aluminum privacy gates for pedestrian entrances, side yards, driveways, pools, equipment areas and architectural boundaries. It compares partial privacy, full privacy and privacy-with-airflow systems, then covers current Aluglobus product examples, Heavy-Duty frames, swing and sliding movement, posts, locks, automation, finishes, costs, measurement, installation and nationwide delivery. A privacy gate is a coordinated frame, infill, post, hardware and movement system, not only a solid-looking panel.Partial PrivacyALU20 and ALU40 slats with controlled gapsFull PrivacyT&G, cladding and selected solid-panel systemsPrivacy + AirflowAeroLouver blocks sightlines while ventilatingIn this guide Quick privacy-gate answer What makes a gate private Privacy-system comparison Open, semi-private and full privacy ALU20, ALU40, T&G and AeroLouver Five current product examples Pedestrian versus driveway gates Swing, sliding and cantilever Why the gate frame matters Slat gaps and sightlines Wind, airflow and drainage Security, pools, pets and climbability Posts, hinges, locks and stops Automation and access control Black, woodgrain and custom finishes Material and installed cost Measuring and installation Freight and contractor planning How to compare quotes Buyer checklist Product and market sources Frequently asked questions Final thoughtsSection 01What Is the Best Aluminum Privacy Gate?The best system depends on whether the project needs partial screening, complete visual privacy or privacy with continued airflow. Fast selectionChoose ALU20 or ALU40 slats when the gate should screen the property while allowing light and air through. Choose ALU50-60 or ALU60 T&G when the priority is a no-gap privacy surface. Choose AeroLouver when direct sightlines should be blocked without turning the gate into a completely solid wind panel.ALU20 creates a narrow, detailed slat pattern. ALU40 creates a wider and visually heavier rhythm. A 3/8-inch or 1/2-inch gap can provide strong screening from common viewing positions, but it is not complete privacy from every angle.Tongue-and-groove panels interlock and eliminate the direct gap. This creates full visual privacy, but it also creates more wind surface. The frame, posts, hinges, foundations and operator must be selected for the complete solid leaf.AeroLouver uses angled aluminum blades to block outside sightlines while preserving natural air circulation. It is a strong option for equipment screens, hot side yards and boundaries where a solid face could trap heat or receive greater wind pressure.For most projects, the correct decision starts with five questions: Who is looking through the gate, from what elevation, at what angle, how much airflow is needed, and how large is the moving leaf?Balanced PrivacyALU40 with a controlled gapStrong screening, airflow and a bold modern profile.Maximum ScreeningALU60 T&GNo direct gap for courtyards, side yards and private entries.Privacy + VentilationAeroLouverAngled blades interrupt views while allowing air to pass.Section 02What Makes an Aluminum Gate Private?Profile WidthA wider profile covers more of the gate face with each slat. ALU40 therefore creates fewer openings across the same gate height than ALU20 when both use the same gap.A narrow profile creates more repeated lines and can feel visually lighter. A wide profile creates a more substantial architectural surface.Gap Between SlatsThe gap determines how much direct light and visibility pass through the gate. Aluglobus slat kits commonly offer 3/8-inch or 1/2-inch spacing.A small gap can feel highly private from the front while remaining visible from a sharp side angle. The gap should be evaluated from the sidewalk, driveway, neighboring property and upper-floor windows.Profile Depth and AngleDeep or angled profiles interrupt diagonal views more effectively than thin flat slats. AeroLouver uses this principle by overlapping sightlines without fully closing the air path.Gate Height and Bottom ClearanceA six-foot gate does not provide six feet of screening when the leaf has a large bottom gap or when the driveway slopes downward from the street.Bottom clearance must also accommodate grade, drainage, gate movement, pets and local rules. Reducing it without planning can cause the gate to drag.Surrounding Walls and Fence PanelsA private gate beside an open fence or low wall does not create a private boundary. Gate height, slat lines, post spacing and finish should coordinate with the complete entrance. Profile width, gap, frame depth and viewing angle work together to determine perceived privacy.Section 03Aluminum Privacy Gate System ComparisonGate InfillPrivacy LevelAirflowWind SurfaceVisual CharacterStrong Starting UseALU20 slatsPartial to high partial privacyGood through selected gapsLower than solid panelsNarrow, detailed, linearPedestrian gates, front entries and side yardsALU40 slatsHigh partial privacyGood through selected gapsModerateWide, bold and modernBackyards, driveways and matching fence systemsALU50-60 or ALU60 T&GFull visual privacyMinimal through the gate faceHighSolid, clean and continuousCourtyards, private side yards and enclosed drivewaysAeroLouverBlocks direct sightlinesHigh airflowLower than a fully solid face when engineered correctlyArchitectural angled bladesEquipment areas, hot climates and ventilated privacyCladding gateFull privacyMinimal through the faceHighFlush facade appearanceGate-and-wall continuity and premium architecturePlexiglass or acrylicDepends on opacity and finishMinimal through solid sheetsHighTranslucent, luminous and modernCourtyards and feature entrancesLaser-cut aluminumPattern dependentPattern dependentPattern dependentDecorative and customStatement gates and architectural focal pointsPerformance note: Wind performance depends on the complete frame, openings, gate dimensions, posts, anchors, foundation, exposure and engineering. The table provides selection guidance, not structural approval.Section 04Open, Semi-Private and Full-Privacy GatesOpen and Decorative GatesAn open gate uses larger spaces between slats, pickets, laser-cut openings or transparent panels. It defines the entrance and can improve security without visually closing the property.Open designs work well for front yards where street visibility, landscape views or a more welcoming appearance matter.Semi-Private GatesSemi-private gates use controlled gaps or offset profiles to block most direct views. ALU20 and ALU40 are common examples.They provide a strong balance for side yards and driveways because air passes through the leaf and the gate feels less like a solid wall.Full-Privacy GatesFull-privacy gates use interlocking T&G, cladding, solid sheets or another no-gap assembly.They are appropriate where the entrance protects a courtyard, backyard, equipment area or private driveway. The solid face should be paired with a frame and support system designed for the increased wind load.Privacy With AirflowAeroLouver creates a fourth category. The angled blade geometry blocks direct sightlines while maintaining a path for air.This can reduce heat buildup around pool equipment, outdoor mechanical systems, side yards and utility enclosures. Angled louvers can block direct views while continuing to ventilate the space. No-gap panels create a solid architectural face and greater wind demand.Section 05ALU20, ALU40, T&G, AeroLouver and Specialty Gate ProfilesALU20 Narrow SlatsALU20 uses a narrow approximately two-inch face. The gate contains more repeated slats, creating a detailed modern rhythm.Choose ALU20 when the design should feel refined, open and consistent with a narrow-slat fence. The 3/8-inch or 1/2-inch gap provides partial privacy while reducing the solid wind area.ALU40 Wide SlatsALU40 uses a wider approximately four-inch face. Fewer profiles cover the gate, producing stronger visual weight and a more substantial privacy surface.ALU40 is a strong choice for modern pedestrian gates and driveway gates where the owner wants privacy without eliminating airflow.ALU50-60 and ALU60 Tongue-and-GrooveT&G profiles engage with one another and remove direct gaps. Black creates a monolithic modern appearance, while woodgrain creates the visual warmth of timber without using wood as the main infill.Use the correct Heavy-Duty or approved frame for wide, tall or frequently operated leaves.AeroLouverAeroLouver uses curved or angled blades at a fixed pitch. The outside view is interrupted while air continues through the profile assembly.Blade orientation should be coordinated with the approach direction and desired privacy side. A louver that blocks one sightline can behave differently when viewed from above or from the reverse side.Cladding, Acrylic and Laser-Cut InfillCladding profiles create a flush gate face that can match an exterior wall. Acrylic can transmit light while obscuring detail. Laser-cut panels can create partial screening with a custom pattern.Specialty infill changes attachment, weight, expansion, cleaning, replacement and frame requirements. Select the infill before the gate frame is finalized.Section 06Five Current Aluminum Privacy Gate ExamplesThese current 4-by-6-foot examples show how slat width, frame category, finish and full-privacy construction affect the material price. Prices checked August 5, 2026Prices were recorded from the live Aluglobus gate catalog on August 5, 2026. Promotions, inventory, product names, dimensions, options, freight and taxes can change. The live product page and written order confirmation control the final material price and included components. Installation is separate unless a written proposal includes it.Example 1 · Narrow Slat Partial PrivacyALU20 Black 4′ × 6′ Universal DIY Gate$976.52This system uses narrow horizontal slats with a selectable 3/8-inch or 1/2-inch gap.It provides airflow and strong screening in a standard wall-to-wall pedestrian opening.ALU20Partial privacyUniversal DIY View current productExample 2 · Wide Slat Partial PrivacyALU40 Black 4′ × 6′ Universal DIY Gate$979.42This product uses wider ALU40 slats while remaining close in current price to the ALU20 example.The wider face creates fewer lines and a visually heavier modern gate.ALU40Wide slatUniversal DIY View current productExample 3 · Black Full PrivacyALU60 T&G Black 4′ × 6′ Heavy-Duty Gate$1,235.40This Contractor Line system uses a stronger frame and interlocking black T&G panels with no direct gap.It is a strong starting point for a private courtyard or side-yard entrance.Heavy-DutyT&GFull privacy View current productExample 4 · Woodgrain Full PrivacyALU50-60 T&G Woodgrain 4′ × 6′ Heavy-Duty Gate$1,456.93This system combines no-gap privacy, Heavy-Duty framing and a woodgrain finish.The additional cost reflects both the decorative finish and the complete solid-panel configuration. Posts, lock, freight, concrete and installation remain project-specific.WoodgrainHeavy-DutyNo gap4 × 6 View current productCurrent ProductPricePrivacyFrameAirflowImportant ReviewALU20 Black 4′ × 6′$976.52PartialUniversal DIYGoodWall-to-wall fit, final gap and lockALU40 Black 4′ × 6′$979.42High partialUniversal DIYGoodGap, mounting surfaces and clear openingALU60 T&G Black 4′ × 6′$1,235.40FullHeavy-DutyMinimal through faceWind, posts, hinges and foundationALU50-60 T&G Woodgrain 4′ × 6′$1,456.93FullHeavy-DutyMinimal through faceWind, woodgrain matching and support systemSection 07Pedestrian Privacy Gates Versus Driveway Privacy GatesPedestrian GatesA pedestrian privacy gate commonly serves a side yard, pool equipment area, courtyard or garden entrance. Four-foot widths are easier to control than a large driveway leaf.Important details include the hinge post, latch post, lock backset, self-closing requirement, bottom clearance and whether the gate opens over rising grade.A six-foot-wide single leaf creates more leverage and wind surface than a four-foot leaf. The frame and posts should be selected accordingly.Driveway GatesA driveway privacy gate can be double swing, tracked sliding or cantilever. Large solid panels create substantial wind reactions and should not be treated as enlarged pedestrian gates.Driveway systems require vehicle clearance, side room, posts, foundations, stops, automation and safety planning.Partial-privacy ALU20 or ALU40 can reduce the solid wind face compared with T&G. Full privacy can still be used when the frame, posts and operator are designed for it. A large privacy driveway gate needs driveway-scale posts, hinges, foundations and center hardware.Section 08Single Swing, Double Swing, Sliding and Cantilever Privacy GatesSingle SwingA single leaf creates one uninterrupted privacy surface. It requires a complete swing arc and a strong hinge side.As the leaf becomes wider, hinge leverage and wind exposure increase. A wide solid single gate can demand a Heavy-Duty frame and substantial post.Double SwingDouble swing divides the opening into two shorter leaves. Each leaf has less individual leverage, but the system requires two aligned hinge sides and center hardware.Privacy at the center joint depends on the overlap, stop, gap and closing sequence. Do not leave a wide center opening that defeats the privacy goal.Tracked SlidingA tracked sliding privacy gate moves parallel to the fence line. It needs a long frame, wheels, a straight track, guide rollers, receiving catcher, stops and side backrun.The gate face remains visible while open, so landscaping and wall layout should account for the stored panel.Cantilever SlidingA cantilever gate avoids a track across the driveway. The leaf includes a counterbalance tail, making the total frame longer than the clear opening.Solid privacy infill adds wind surface to the extended frame. Roller posts and foundations require project-specific engineering.Section 09Why Privacy Gates Need a Real Structural FrameA gate without a frame is only a fence panel with hinges. Privacy infill makes frame design even more important because the leaf is heavier, catches more wind and is operated repeatedly.Perimeter FrameThe vertical sides carry hinge and lock forces. The top and bottom members keep the leaf square. Reinforced corners transfer loads between the members.The infill should be retained inside the frame or by a system designed to connect to it. Slats alone should not act as the primary gate structure.DIY Versus Heavy-DutyUniversal DIY frames can work well for controlled wall-to-wall pedestrian openings. Heavy-Duty or Contractor Line frames are better for wider leaves, solid privacy panels, frequent use and demanding installations.Automation should not be added to a basic frame without confirming operator attachment, post strength and repeated load transfer.Deflection and SagA privacy gate can remain square at installation and then move after months of wind, heat and daily operation. Frame depth, wall thickness, corner construction and hinge spacing affect long-term alignment.Correcting sag after the finish is complete is more expensive than selecting the right frame before fabrication.Gate Posts and WallsThe strongest gate frame cannot compensate for an undersized post, weak wall or thin slab. The support system must transfer the leaf loads into a suitable foundation.Compare frame specifications before comparing slat colors. A premium infill inside a weak frame can still sag, bind, miss the lock or overload the motor.Section 10Choosing the Right Slat Gap and Sightline3/8-Inch Versus 1/2-Inch GapsA 3/8-inch gap provides slightly more screening and slightly less airflow than a 1/2-inch gap. The visible difference depends on the profile width and viewing distance.With ALU40, either gap occupies a smaller proportion of the gate face than it does with ALU20.Direct and Diagonal ViewsStand at the expected viewer locations and look through a sample at the intended height. A gate that appears private from directly in front may open visually when viewed from the side.Deep slats, offset layouts and AeroLouver profiles improve diagonal screening.Views From AboveSecond-story windows, raised neighboring lots and uphill streets can see over or through a gate differently from ground-level pedestrians.Increasing height may be limited by zoning or gate movement. Landscape, wall design and overhead screening can sometimes solve a view that the gate alone cannot block.Aligning the Gate With the FenceHorizontal slat lines should continue through adjacent fence panels when grade allows. The gate frame can change the available infill height, so the pattern should be set before slats are cut.A mismatch becomes especially visible on wide double-swing gates.Section 11Wind, Airflow, Heat and DrainageSolid Privacy and WindT&G, cladding and solid sheets block air through the gate face. Wind pressure transfers into the frame, hinges, posts, anchors and foundation.Open hillsides, coastal properties, corner lots and long driveways can be more exposed than protected side yards.Slat GapsALU20 and ALU40 gaps release some pressure while providing screening. Increasing the gap can reduce wind surface but also reduces privacy.Do not select a gap from privacy alone when the gate is very large or highly exposed.AeroLouver AirflowAngled blades allow air to move through a non-direct path. This can help ventilate equipment and reduce heat buildup behind the gate.The louver assembly still creates wind load. Blade geometry, spacing and frame design must be evaluated as a complete system.Drainage and DebrisBottom rails and channels should not trap irrigation water, leaves or soil. Keep weep paths clear and protect the finish from standing debris.A low privacy gate over sloped paving needs enough clearance to move without dragging while still limiting the view beneath the leaf.Section 12Security, Pool Barriers, Pets and ClimbabilityPrivacy Is Not the Same as SecurityA solid-looking gate blocks observation, but security also depends on frame strength, posts, hinges, lock, latch protection, height and resistance to lifting or forced opening.Complete privacy can conceal activity on both sides of the gate. Cameras, intercoms and controlled visibility may be useful at a main entrance.Pool GatesPool barriers can require self-closing and self-latching gates, controlled openings, minimum height and non-climbable design.Horizontal slats can create ladder-like footholds depending on spacing and profile position. Verify the final system with the authority having jurisdiction.Children and PetsSmall gaps can prevent pets from pushing through the gate face. Bottom clearance, hinge gaps and the space at the receiver side are equally important.A pet-resistant gate should not trap paws, heads or tails in moving joints.Emergency and Egress AccessLocks and access control should allow required emergency release and egress. A high-privacy gate should not block a required exit or emergency access route.Section 13Posts, Hinges, Locks, Stops and ClosersHinge PostsThe hinge post carries the gate weight, leverage and wind reaction. Embedded posts rely on footing depth and concrete. Surface-mounted posts rely on slab thickness, reinforcement, base plate and anchors.Stucco, veneer and decorative wall caps are not structural support by themselves.HingesAdjustable Heavy-Duty hinges allow alignment after installation. Hinge quantity and spacing should match leaf height, width, weight and use.A full-privacy leaf can place different demands on the hinge system than an open slat leaf of the same size.Locks and LatchesConfirm the stile width, lock backset, strike location, handle clearance and cylinder preparation. Electric strikes, magnetic locks and gate locks require different frame details.Stops and Center HardwareA swing gate should close against a designed stop rather than using the lock to absorb movement. Double gates can need drop rods, center stops or an inactive-leaf bolt.ClosersHydraulic or spring closers must be sized for the leaf and adjusted for safe closing speed. Wind can cause a solid privacy gate to close faster or resist closing. Hardware should be selected with the frame and post system before fabrication begins.Section 14Automating an Aluminum Privacy GateOperator SizingOperator selection should consider leaf length, weight, wind surface, movement, hinge geometry, speed and daily cycles.A lightweight aluminum privacy gate can still require a substantial operator because wind pressure acts across the complete face.Motor-Ready FrameThe operator bracket repeatedly applies force to the gate. The attachment point should have structural backing and should not rely on an infill slat.Sliding gates need a suitable gear rack or chain attachment. Swing gates need bracket geometry compatible with the post and opening angle.Entrapment ProtectionAutomated systems require safety planning such as monitored photo eyes, safety edges, guards, loops, warning signs and emergency release.Solid privacy gates can hide a person, vehicle or object from an operator on the opposite side. Sensor coverage should account for the obstructed view.Access ControlKeypads, cellular controls, remotes, intercoms, card readers and cameras should be located where a visitor can use them without standing in the gate path.Plan power, conduit, control boxes, battery backup and service access before concrete and gate fabrication.Section 15Black, Woodgrain and Custom Privacy Gate FinishesBlack Powder CoatBlack creates a strong modern silhouette and visually reduces the appearance of gaps in many slat layouts.Compare pretreatment, powder specification, texture, gloss and warranty rather than only the word black.Woodgrain AluminumWoodgrain provides the appearance of timber without using wood as the primary gate infill. It does not require routine staining or sealing.Grain direction should continue across the leaf and coordinate with nearby fence panels. Double gates should be laid out as one composition.Custom ColorsCustom RAL colors can coordinate the gate with windows, cladding, railings and patio systems. Custom production may add setup, sample approval and lead time.Coastal and High-Exposure PropertiesRinse salt and pollution from the coating. Protect cut edges, hardware connections and impact damage. Woodgrain creates a warm privacy surface while the structural perimeter remains visible. Translucent panels can obscure detail while allowing light into the entrance.Section 16How Much Do Aluminum Privacy Gates Cost?The material price depends on gate dimensions, frame category, infill, finish and movement. The installed project also includes posts, concrete, hardware, freight, labor and possible automation.Partial-Privacy Pedestrian GatesCurrent 4-by-6-foot Universal DIY ALU20 and ALU40 material examples are priced near $977 to $980.These are complete gate-kit examples, not installed-project prices. Confirm posts, locks, freight and site work separately.Full-Privacy Pedestrian GatesThe current Heavy-Duty black T&G example is $1,235.40, while the Heavy-Duty woodgrain T&G example is $1,456.93.The price increase reflects the Heavy-Duty frame, complete no-gap infill and premium finish.Driveway and Sliding Privacy GatesLarge double-swing and sliding gates use substantially more frame and infill. Current Aluglobus sliding products can extend from the high $2,000s to more than $5,000 for material before motors and installation.Installed Project CostThe completed budget can include demolition, posts, foundations, masonry, track, operator, safety devices, electrical service, access control, freight, equipment and professional labor.Use the separate Aluminum Gate Cost in 2026 guide for broader material and installed planning ranges.Section 17How to Measure and Plan InstallationMeasure Finished SurfacesMeasure between finished walls or posts at the top, middle and bottom. Stucco, stone, caps and cladding reduce the rough opening.Confirm whether the product dimensions describe the gate leaf, nominal opening or complete system.Map the GradeRecord finished paving and the complete swing path. A gate that clears the ground while closed can strike a rising walkway while opening.For sliding gates, confirm a straight travel line, track area and side backrun.Confirm Handing and DirectionMark the hinge side and opening direction on a photograph or plan. Do not rely only on verbal left-hand or right-hand descriptions.Measure Privacy SightlinesDocument the sidewalk, street, neighbor and upper-floor views the gate needs to block. This helps select gap, profile and height.Install the Support System FirstPosts should be plumb and stable before the gate is hung. Confirm foundation curing, anchors, wall strength and stop locations.Step 01Measure the openingRecord top, middle, bottom, grade and finished surfaces.Step 02Define privacyIdentify viewing angles, desired airflow and bottom clearance.Step 03Select structureChoose frame, posts, hinges, lock, stops and foundations.Step 04Coordinate movementVerify swing arc, slide backrun, automation and safety.Section 18Nationwide Shipping and Contractor PlanningConfirm the Complete OrderVerify product, dimensions, frame category, slat gap, finish, handing, posts, hinges, stop, lock preparation and quantity.Do not assume a product title includes every post or hardware component. The written order should control the final package.Plan Freight and UnloadingLong profiles and gate frames normally ship by freight. Ask for packaged dimensions and weight before dispatch.A residential liftgate may not unload a long driveway-gate crate. Some shipments require a forklift, dock or several people.Inspect DeliveryPhotograph the crate before unloading and note visible damage on the carrier paperwork. Keep packaging until all components have been checked.Store CorrectlyStore profiles flat, supported, dry and away from concrete dust, welding sparks, chemicals and construction traffic.Contractor TakeoffContractors should prepare a complete takeoff that separates gate kit, posts, concrete, locks, automation, freight and labor.Section 19How to Compare Aluminum Privacy Gate QuotesCompare the Same Privacy LevelA 1/2-inch ALU20 gate is not equivalent to no-gap T&G, AeroLouver or cladding. Compare profile, gap, depth, viewing angle and airflow.Compare the Same FrameList frame dimensions, wall thickness, corner construction, reinforcement and motor preparation.Compare Posts and FoundationsConfirm post size, length, base plate, anchors, footing, wall attachment and whether structural site work is included.Compare HardwareList hinges, lock, handles, closer, stops, drop rods, track, wheels, guides and catcher.Compare FinishCompare pretreatment, powder standard, texture, gloss, color and woodgrain process.Compare Automation and SafetyIdentify operator model, number of motors, safety devices, loops, access control, electrical work and commissioning.Compare Freight, Labor and WarrantyClarify crating, delivery, unloading, installation, cleanup, product warranty, finish warranty and labor warranty.Section 20Aluminum Privacy Gate Buyer ChecklistIdentify pedestrian, courtyard, equipment or driveway useMeasure the finished opening at the top, middle and bottomRecord slope, paving and the complete movement pathChoose partial, full or privacy-with-airflow performanceSelect ALU20, ALU40, T&G, AeroLouver or specialty infillSelect the gap and evaluate direct and diagonal sightlinesReview second-story and elevated neighboring viewsSelect Universal DIY, Heavy-Duty or custom framingConfirm single swing, double swing, sliding or cantilever movementSize hinge and receiver posts for the complete gateConfirm footings, anchors, walls and existing slab conditionsSelect hinges, lock, closer, stops and double-gate hardwareReview wind exposure and solid-panel surface areaReview pool, pet, climbability and emergency-access requirementsPlan operators, safety devices, power and access control earlySelect black, woodgrain or custom architectural finishCoordinate gate slats with adjacent fence and wall systemsConfirm freight, unloading, storage and installation accessCompare complete system quotes, not only the gate leafUse the live product page and written order for final pricingSection 21Product and Market Sources Aluglobus Aluminum Gate Systems DIY, Heavy-Duty, ALU20, ALU40, T&G, Plexiglass, cladding and AeroLouver options. Current Aluminum Gate Catalog Live factory-direct products, dimensions, configurations and pricing. Aluminum Gate Kits Buyer’s Guide Frame-only, Universal DIY and Heavy-Duty kit selection. Aluminum Gate Cost Guide Material, installation, automation and total-project budgeting. DIY Versus Heavy-Duty Frames Application limits, frame strength and contractor planning. AeroLouver Curved Blade Angled aluminum profile for privacy, ventilation and architectural screening. Section 22Frequently Asked Questions About Aluminum Privacy Gates What type of aluminum gate provides the most privacy?An interlocking ALU50-60 or ALU60 tongue-and-groove gate provides the most direct visual privacy because the panels connect without a visible gap. Cladding and selected solid-sheet systems can also create full privacy. ALU20 and ALU40 slats provide partial privacy with airflow, while AeroLouver blocks direct sightlines through angled blades. What is the best slat gap for an aluminum privacy gate?A 3/8-inch gap provides slightly more screening than a 1/2-inch gap, while a 1/2-inch gap allows slightly more light and airflow. Privacy also depends on profile width, slat depth and viewing angle. A no-gap T&G system is better when complete visual privacy is required. Does a full-privacy aluminum gate need a Heavy-Duty frame?Many full-privacy gates benefit from a Heavy-Duty frame because solid panels increase wind surface and can add material weight. The correct frame depends on gate width, height, movement, wind exposure, daily use, posts and automation. A standard pedestrian leaf and a large driveway leaf should not use the same assumptions. Can an aluminum privacy gate allow airflow?Yes. ALU20 and ALU40 gates allow air through the selected slat gaps. AeroLouver provides stronger visual screening by using angled blades that interrupt direct sightlines while maintaining natural ventilation. A no-gap T&G or cladding gate provides less airflow through the gate face. Can a full-privacy aluminum driveway gate be automated?Yes, but the operator, frame, posts, hinges or sliding hardware, foundations and safety devices must be selected for the complete leaf. Full-privacy panels catch more wind than open slats. The operator bracket should attach to structural reinforcement, and monitored safety devices should account for the blocked view through the gate. How much does an aluminum privacy gate cost?Current Aluglobus 4-by-6-foot partial-privacy ALU20 and ALU40 Universal DIY kits are listed near $977 to $980. Current 4-by-6-foot Heavy-Duty T&G privacy examples range from $1,235.40 in black to $1,456.93 in woodgrain. Posts, locks, freight, concrete, automation and installation are separate unless included in writing. Final ThoughtsChoose Privacy as a Complete Gate SystemAluminum privacy gates can provide controlled screening, complete visual separation or privacy with continued ventilation. The correct result comes from more than selecting a solid-looking product photo.ALU20 creates narrow architectural lines and partial privacy. ALU40 creates a wider and visually heavier gate face. T&G panels eliminate direct gaps. AeroLouver blocks sightlines while allowing airflow. Cladding, acrylic and laser-cut systems create additional architectural options.As the gate becomes wider, taller and more private, frame strength, wind reaction, posts, hinges, foundations and automation become more important. A privacy gate without the correct frame and support system can sag, bind, overload hardware or move in the wind.Define the required sightlines, airflow, movement and use before selecting the finish. Then compare complete dimensions, frame, infill, posts, hardware, freight and installation. That process produces a privacy gate that looks intentional and continues to operate as a real entrance system.